Trial 2 DIY Aerial Costumes: Fabric Paint and Rhinestones

This is my second attempt at making an aerial costume. I had a white cotton unitard with wide legs (not tight like I would want for aerial routines) that had been laying around for a few years because it was an “On SALE” mis-order that I couldn’t return. I finally decided to give fabric painting a try.

  1. I started the by sketching a pattern of what I wanted my swirls to look like then I colored them in.
  2. I put the unitard on my inflatable mannequin (bought off ebay $25) and took a pencil and drew outlines of the shapes.
    iphone - 42
  3. I put Jacquard Water Based Resist in a Jacquard 1/2 ounce squeeze bottles with stainless steel tips (see below for list of supplies) and outlined my design.
    iphone - 45
  4. I used Jacquard Dye-Na-Flow to fill in the design. I put the paint (which looks and feels like fabric dye) in the small 1/2 oz squeeze bottles. I used a very small amount on a paint brush and applied it to the fabric.
    iphone - 64
    iphone - 62
    It spreads very quickly and you need to be very careful that it stays in the lines.
    iphone - 66
    NOTE: I should have made my water resist lines thicker because the paint (dye) bled out quite a bit.
  5. I had to “fix” all these areas where the paint bled through. I took white textile paint and touched up the design. You can sort of see the paint but from a distance it looks OK.
    iphone - 93
  6. Next, I took Jacquard Textile paint and outlined the design and made some high and low-lights around it.
  7. Then I ironed to set the paint into the fabric.
    iphone - 106
  8. Time for some rhinestones. I separated them by color and size.
    iphone - 90
    Then I planned out the order that I wanted to attach them and put them into lines.
    iphone - 105
  9. Attaching rhinestones is very easy. I watched a few You Tube videos on How to Embellish Dance Costumes. I used E600 and a Jewel Setter (a stick with a bit of wax at the tip. You can get them at Michaels or a craftstore and they help A TON!).
    iphone - 108

    Finished product:

I like it. It isn’t professional and I wouldn’t use it for a paid performance but it was a great learning experience. I now know how these paints work on stretchy fabric. I learned about water based resist, dye-na-flow, and other design aspects. It still needs some work but …I like it.

iphone - 110

 

Supplies I’ve acquired during the past few years.

Fabric paint:

Some I had purchased in 2014. I’m not sure how much I paid for it. The new paint I’ll put purchase prices for reference. Fabric paint isn’t cheap unless you know the exact colors you want. Otherwise it all adds up pretty fast.

Jacquard Textile: For Natural Or Synthetic Fabrics

  • 122 Black. Very thick paint. Used about 6 months ago to paint over the logo on my bouldering crash pad. It covered the bright orange in two coats.
  • 123 White
  • 111Sky Blue
  • 114 Turquoise
  • 155 Fluorescent Blue
  • 151 Fluorescent Yellow: very light, could not be seen very well on white fabric.
  • 153 Fluorescent Pink. (2.25 oz.) Amazon $7.96
  • 156 Fluorescent Green. (2.25 oz.) Amazon $5.72

2016-03-27 09.59.03

Jacquard Lumiere: Light Body Metallic Acrylic

  • 561 Metallic Gold: 2 bottles purchased about 10 years ago for a Wonder Woman costume. One bottle opened and 2/3 empty. The paint was very thick but it still worked fine.
  • 567 Super Sparkle
  • JAC9901 Halo & Jewel Colors Lumiere Exciter Pack, 9 Color (0.5 oz. bottles): Halo Pink Gold; Halo Blue Gold; Halo Violet Gold; Pearlescent Turquoise; Pearlescent Green; Pearlescent Magenta; Russet; Pewter; Sunset Gold. Amazon $9.99

2016-03-27 09.59.16

Jacquard Dye-Na-Flow: Free Flowing Liquid Color For Natural or Synthetic Fabrics

  • 830 White
  • 801 Sun Yellow
  • 824 Azure Blue
  • JAC9908 Dye-Na-Flow Exciter 9-Colors (0.5 oz. bottles): Chartreuse; Turquoise; Periwinkle; Violet; Magenta; Scarlet; Bright Orange; Golden Yellow; Sun Yellow. Amazon $11.65

2016-03-27 09.59.33

Jacquard Water Based Resist

2016-03-27 10.00.06

Other stuff

Tulip Glitter Spray Fabric Paint – 40 oz. Michael’s $7.49 (on sale $5.99) *Looked great when I tried it. It was a sheer glitter but I’ve been told that it doesn’t hold up well when washed.  It was easy to do so maybe this is for that costume that you wear once and then have time to re-spray after washing for the next use.

Tulip Glow in the Dark Spray Fabric Paint – 40 oz Michael’s clearance $2.99

Jewel Spinner with Rhinestones – Michael’s $2.99 (on sale $2.40)

Tools:

  • Cardboard
  • Water bowl
  • Paint brushes- assorted
  • Foam brush
  • Pencil
  • Scissors – Michael’s Bent 365 $12.99 40% off = $7.79 (to be fabric only scissors)
  • Jacquard 1/2 ounce squeeze bottles with stainless steel tips
  • Bead pick (plastic stick with wax on tip to place rhinestones) – Michael’s $4.99 for 3 (on sale $3.99)
  • Stencils
  • Paint pallet with cover -Michael’s $1.59
  • Mannequin – Inflatable Female EBay

2016-03-27 10.01.15

 

Trial 1 DIY Aerial Costumes: Fabric Paint, Cutting, & Rhinestones

This blog goes through some trial DIY aerial costumes. The first is just an old tank top that I test painted. The second I had an old unitard I was going to throw away. I re-dyed and cut, painted and rhinestoned to make it special and customized.

Intro:

I don’t know how to sew and I never had a nack for drawing or painting. Soo…I thought it would be a great endeavor to make myself some aerial costumes. (I don’t know why I always think I can do these crazy things…) I started by brainstorming ways to create…since I cant sew I needed to start with a pre-made base.

I was looking discount leotards, unitards, and biketards (I didn’t know if I was going to be any good at costume making so I wanted to keep it cheap). I did a web search and pinned a bunch of potential items. I tried to keep it “cheap” cotton, white or nude. Here is my Pinterist page.

NOTE: I had been thinking about making a costume a few years ago but never actually got around to doing it. I had 2 cotton white unitards (one has tight legs and the other has wide legs (the wide leg one was a mis-order & not what I wanted for aerial but it will be a good trial piece). I also already had a good base of fabric paints in metalics, blue, yellow, white and black. (And I was slowly buying more and more. I need to stop my visits to Michaels and my late night Amazon shopping binges.)

I’m also creating a list of awesome aerial costume makers/websites because although I am loving costumes that I make myself sometimes you need a professional costume. Please leave a comment if you have other DIY costume ideas or know an awesome aerial makers.

Trial tank top:

First I started by drawing some different ideas out on some paper. I was trying some swirls and other patterns. I have little or no artistic talent when it comes to drawing…but I’m going to see where it goes.

2016-03-27 09.59.48

Then I took an old tank top that I was going to throw away and put some cardboard between the layers and sketched some lines with a pencil. Then started painting.

Meh, not that great but that’s why its an old tank that I was just testing my skills on. It does look better on than on the table…

F2016-03-27 16.42.53

Trial Unitard: Old light pink cotton unitard

It was stretched out and faded and has a few holes starting in the leg and crotch. I was going to throw it away but then I stopped and thought it would be a great piece to start with because if I ruined it I wouldn’t feel bad…I’d just have wasted a ton of time. It took me an afternoon to dye, cut, and paint (we went out to dinner while the front was drying and I finished painting the back that evening). Then the next morning I ironed and added rhinestones (which took less than an hour).

Ombre Fabric Dye:

I wanted to refresh the color and I had a package of Dylon Flamingo Pink fabric dye that I had purchased 6 or 7 years ago and never used. This is the video I tried to follow. Ombre fabric dye video.

  1. Wash without using fabric softener.
  2. I put the unitard on and marked it with safety pins where I wanted to gradients to be (chest, hips, knees).
  3. I found a hanger and some ribbon and I used my laundry room cabinets to make “hooks” so I wouldn’t have to hold the unitard all the time.
  4. Then I got the unitard wet and rang it out.
  5. I set up my bucket in the sink. I also set out the dye, salt, measuring spoon, scissors, plastic spoon to stir on the counter.2016-04-02 14.38.55
  6. I heated water up in the microwave in a plastic bowl and dissolved the fabric dye and added the salt.
  7. I made sure the tap water was very hot and started filling my bucket in the sink. Then I added in my fabric dye mixture.
  8. I submerged the unitard up to the waist and kept dipping it from waist to knees for about 20 min.
  9. Then for about 10 min I dipped it from chest to waist.2016-04-02 14.38.22
  10. Then let it sit for about 10 more minutes hanging with just the knees to the bottom in the bucket.2016-04-02 14.39.10
  11. Then I rinsed the unitard until it ran mostly clear.
  12. Then put it through my washer and dryer. 2016-04-02 15.58.38

Cutting:

I’ve seen some instagram posts and a YouTube video by Adam Slacks with a unitard that has been cut up and I really liked that look. I wondered if I could do it myself. I had tried to cut a t-shirt before and it turned out OK…so I decided to give it a try.

I used pins from Pinterest for inspiration:

Steps:

  1. I put the unitard on and kept the safety pins in to mark body landmarks (chest, hips, knees).
  2. Then I took a pencil and marked where I wanted to make my cuts.
  3. I used a piece of cardboard inside the unitard to help stretch it out and keep shape.
  4. I used a ruler to help keep the lines straight but I ended up eyeballing most of the cut.2016-04-02 17.30.12
  5. As I braided I used the safety pins to hold the final braid in place.
    2016-04-02 18.10.57
  6. Then I just used a simple thread and needle and sewed the end of the braids together with knots.
  7. I bought an inflatable dress mannequin from ebay for about $25
  8. I kept it on the mannequin for the painting and rhinestones.
  9. I used a pencil to draw some swirls then painted some silver and pink swirls. With the silver at the top and the pink towards the bottom to keep with the ombre feel.
    iphone - 19
  10. Then finally I put some rhinestones on it with the clear crystals at the top and the pink crystals towards the bottom.
    iphone - 18
  11. Finally, I put it on and tried it out on my hoop. Fiphone - 24Fiphone - 29

NOTE: Cutting will make the size change sometimes smaller and sometimes larger. The S curve cut/braid really pulled the fabric out of line and it was too small for me. It ripped on my first trial. Nothing that couldn’t be fixed because…well its already cut up. But I suggest a few trial runs before using a cut unitard in a performance to make sure the cuts don’t rip in inappropriate areas.

Save

Aerial Equipment part 5: Rust on my Lyra (Cleaning, Painting, Re-taping)

II’ve had my Lyra for over 8 months. I’ve brought it into studios and used it on my outdoor rig. I still love it! Most of the time it is stored inside in my dance room which is air conditioned yet about 2 months ago it started to rust through the tape. I live in Florida where the humidity is very high. It is possible that I set my hoop down in wet grass or something. I’m not exactly sure why it is rusting. I’ve been busy but it has reached the point that it is time to clean off the rust on my hoop and re-tape. Basically, make it pretty again.

These are the “before” pictures as I was taking off the tape. It was really pretty disgusting.

I needed to start my research again to figure out the best way to do this…

I opened Facebook on my laptop and went to the Safety in Aerial Group. I knew I had read about ways to clean and re-tape your hoop in some of the posts. I plugged “rust” into the search bar and started reading.

This is what I found:

Yes, other people have this problem. Probably, the best way to solve it is to have it powder-coated (or to have bought a stainless steel or aluminum hoop to begin with…). Well, I’m not ready to make the powder-coating leap yet. So I’m going to start by cleaning it.

Suggestions for cleaning it:

  • Use steel wool to clean the rust off (Grade #0 Fine did not work)
  • Use 200 grit sand paper to clean the rust off (When I spoke to one of my aerial instructors this is what she has done in the past. This is also what worked the best for me.)
  • Use 3M Scotch-Brite General Purpose Hand Pad to clean the rust off (This helped get the dirt grime off but didn’t really see it get rust off.)
  • Use Navel Jelly to dissolve the really stubborn rust off (You can buy it at Home Depot. Use gloves & do it outside. I did not actually need to use it but its good to know & have on hand.)
IMG_9577

Cleaning supplies

Keep it from rusting:

After cleaning it there were several suggestions on how to keep it from rusting again.

  • Powder-coating (I’ll look into this in the future but right now I’m trying some other things)
  • Oiling/lubricating (It would probably work but I’m having a mental block about putting oil onto an apparatus that I’m going to be hanging from…):
    • Sentry Solutions Marine TUF-CLOTH to stop the rust
    • T-9 Boshield to protect the metal from rust. This was copied from the Boshield website “T-9 dries to a waxy, waterproof finish without leaving a sticky film.” (you can buy it at any woodworking store)
    • FYI: W-D 40 does not protect from rust.
  • Spray painting (use Rust-Oleum or Kyrlon Hammer Finish)
  • Taping and putting a coat of acrylic paint over it

I decided to try to clean it the best I could. Use Rust-Oleum to paint it. Then re-tape it. I read that several studio owners do this but they need to re-do it about twice a year. I will try and and report how it does in future posts.

My process

Cleaning the hoop

  1. I took all the tape off
  2. Then I started cleaning. I took it outside and started with the steel wool.
    IMG_9579

    Steel Wool.

    I went through 2 pads before I realized it wasn’t really doing anything. I was using the “Grade 0: Fine” steel wool. Maybe this wasn’t tough enough.

  3. The steel wool was actually sticking to the left over adhesive. So I went and found some GOO GONE and a rag and started wiping the adhesive off. That really helped.

    IMG_9580

    GOO GONE!

  4. That’s when I noticed that the cement pavers on my patio were scratching my metal hoop so I found an old towel to put down to protect it.
  5. Not to worry because I switched to the 220 grit sand paper and that really started to clean it up. The sand paper cleaned off the rust and a lot of the black dirt. It also filed down any of the scratches that were rough. My hoop started getting shiny.
    IMG_9581

    Protect the hoop from scratching on concrete.

    This was extremely dirty and my hands, arms, face, shirt all started turning black. LOL. It was so messy & I was outside in 90 degree heat so it was everywhere.

    IMG_9584

    So dirty!

    IMG_9585

    Result of my cleaning supplies.

  6. Then I found a Scotch-Brite sponge scrub pad and some dish soap to wash it. I took a garden hose and soaped it up.
    IMG_9586

    Dawn and Scotch-Brite Scrub Pad.

    Initially, I was just going to use the sponge but once I started washing it a lot more of the black, dirty grime started coming off. I switched to the green scrub side and this REALLY helped clean the hoop up. Now it was shiny!

  7. I dried it off with a towel and set in out in the sun to dry.
    IMG_9587

    Its all clean and shiny!

    IMG_9588

    Look at the shine. No more rust.

What I would do differently

If I were to do this again (and I’m not sure how it will work now that I’ve spray painted the hoop)…

  1. After removing the tape, I’d wash it first with the sponge and soap
  2. Use the GOO GONE right away
  3. Then maybe take the Scotch-Brite scrub to it
  4. If there is still grime and rust then I’d use the sand paper
  5. And finally if needed I’d use use the Navel Jelly.

Spray painting the Lyra

This was easy. I saved this screen shot from Steve Santos with the idea of following it to a T.

IMG_9557

Screen Shot from a Facebook’s Safety in Aerial discussion about rust on hoops.

I went to Home Depot to buy supplies and called my Fiance to see if we had a “torch.” We do but he told me I didn’t need to use it (I think he didn’t want me burning down the house.). That all I needed to do was leave the hoop in the Florida sun to heat up and dry off all the moisture. I understand that there is still a ton of moisture in the air and I probably should have heated the hoop up but I’m learning to pick & choose my battles with my Honey Bunny and this was one I didn’t want to fight so I let it go. My hoop did get very hot in the sun so hopefully it worked **Fingers crossed**

  1. Bought Rust-Oleum Primer and Spray Paint. The color isn’t going to matter but I really liked the light metallic champagne pink color.
    IMG_9576

    Spray paint!

    ***LOOK at this sparkly  glitter spray paint. OMG! I didn’t know if I’d actually use it but it was too cool not to buy. I was thinking about using it and not taping the hoop and maybe the glitter would act a bit more grippy. When I mentioned this to my Fiance he didn’t think the glitter paint would stay on very long and would scratch/peel off right away with use. Anyone have thoughts on this? I’m not brave enough to try it yet***

  2. I hung it on my rig outside by one spanset and started spraying the primer.
    IMG_9593

    Hung it outside from one spanset.

    I did a light coat about 6-12 inches away from the hoop. Let it dry for about an hour. then moved the spanset to the other side and did another light coat. Then I let it dry for 2 hours and brought it inside to dry overnight.

    IMG_9595

    First coat of primer.

  3. Then the next day I did the same thing with the champagne pink spray paint. It actually started raining about an hour after I sprayed. Once it stopped I took it down and dried it off and set it inside to finish drying.
    hoop

    Metallic Champagne Pink Spray Paint. I LOVE this color!

    hoop2

    Its almost the same color as my wall.Taping my Lyra

Taping my Lyra

When I was first purchasing hardware for my Lyra I bought some Mueller’s Athletic tape knowing I’d eventually need to re-tape it. I found it on Amazon.

tape

Mueller Tape 3 rolls, 1 1/2 inch x 10 yards

tape2

Comes in many colors!

 

This is what I found when searching for how to tape a Lyra (tape an aerial hoop). Its a lot like taping a hula hoop. These are some helpful tips:

  • Tape from the bottom to the top. if you don’t do this then the tape will roll over on itself as your hands/body slides down the hoop.
  • If you look at the hoop as a clock with 12 at the top. Start taping at 7 going up to the top towards 1. Then go the opposite direction starting at 5 and going up towards 11. This gives you some overlap at the bottom where there is most wear.
  • Here is a video that shows a taping tutorial.

In all it took less than 20 minutes and I thought this was the easiest part of this entire process.

  1. I started the tape at 7 on a clock and wrapped around the hoop tube it so it overlapped itself 1/2 the width of the tape.
tape3

Starting the taping.

2. I tried to keep the tape tight against the hoop to keep any wrinkles out.

tape4

I started at about 7 on the clock.

IMG_9665

This was one roll of 10 yards of tape.

3. Once I finished one roll of tape. I took a second roll and started at the 4/5 on a clock and started wrapping clockwise. This roll seemed to have more strings come off the tape. A few times I had to stop and turn my roll of tape over so the other side of the tape was being overlapped to keep it from unraveling. (I guess I’ll see how that works out.)

IMG_9668

The second roll I started at 4/5 and wrapped clockwise.

4. Using the second roll of tape I was able to complete the hoop part and go all the way across the straight part and ended where the hoop starts to curve again. I had just a bit left on the roll.

IMG_9670

Finished! OMG its like I have a new hoop!

5. The hoop is SO BEAUTIFUL. It looks like a brand new hoop! Why didn’t I do this sooner?

IMG_9671

It matches all my other pink stuff.

Please let me know if you have any other suggestions or if you tape/protect your hoop in different ways.

Types of tape that people use to cover their Lyra:

  • Mueller Athletic tape (M-Tape)
  • Generic athletic tape / adhesive cotton tape (ie. Zonas Zinc Free tape)
  • Newbaums handlebar tape (its soft & not sticky)
  • Hockey tape
  • Some people use foam pre-wrap or under wrap under the tape for padding or use several layers of cotton tape
  • Gaffer tape (heavy cotton cloth with strong adhesion properties, typically used to tape down cables to the floor during stage productions, try the brand Polyken, tends to be expensive)
  • Baseball/tennis racquet tape
  • Soft side of velcro tape (??)
  • ESI Silicone tape

Ways to decrease stickiness of a taped hoop:

  • Put chalk on in
  • Coat it with acrylic paint
  • Instead of chalk dust a fresh tape job with shimmer powder
  • Someone posted that “zinc” in the tape is what gives it the sticky goo so look for zinc free tape

UPDATE: 10/16/16 The Mueller Tape that I used is SUPER sticky! It really eats up my hands. I’ve just seen a recommendation for Meister Tape. I think it can be purchased off Amazon. I’ll probably try that next time. 

 

 

Aerial Equipment part 1: Buying a Lyra

***I am NOT an aerial instructor or rigger. I am NOT a professional. My ideas for safety may not be the same as yours or what a professional aerialist/rigger/instructor recommends. Please refer to professionals if you have questions. Facebook Safety in Aerial Arts Group and Simply Circus site are a great resources.***

Originally buying my own equipment wasn’t in my plans. I really didn’t need my own equipment. …but I fell in love with a special lyra.

Last year I took a class at Circus-Arts in Polk City, FL. I practiced on a hoop and we bonded. Csaba had made it himself…a one of a kind. It was the perfect size, shape, and movement for me. I loved it. It stayed in the back of my mind for a long time. Throughout year I attended classes there about once a month, one day I asked him if he would make another for me… or if I could buy that hoop. A few weeks later, I was a new owner of my very own aerial hoop.

It cost $250. Very reasonable price for a hoop. Plus I didn’t have to pay shipping.
*I am finding shipping is a HUGE expense when it comes to buying aerial equipment.
Csaba tried to give me a couple of spansets but I wanted shiny new hardware. (In hindsight, I should have taken those spansets …because although spansets are each fairly inexpensive, when you start buying a few in several different lengths, the price adds up.)

Next, I needed to figure out what hardware I wanted to complete my set up. I would need at least 2 spansets, 2-3 carabiners and a swivel. I knew from being a part of the Safety in Aerials Facebook group that I needed hardware that would hold up a car (2000-5000 lbs).
*A Cadillac Escalade weighs 5,949 lbs.

Where do I find that type of hardware? First, I asked my instructors. Then I went to the most likely websites…ones that sell aerial & circus stuff. These are some of the sites I found but there are many others:

I also went to climbing and rigging websites:

  • Sapsis Rigging -the website is a bit difficult to search but keep at it or call them to help
  • REI (I have not had good luck with specifics from them)
  • Dick’s Sporting Goods
  • Gear Express
  • Rigging Warehouse – its a bit of a process to get registered & order
  • Bill Jackson’s (The only climbing gear store I know about in Tampa Bay)

I’m analytical and enjoy list making and comparisons. I priced everything and looked up ratings. Then I took the info and made charts. All of this was somewhat confusing for me. I’m a newbie to rigging and I wasn’t quite sure what all the terms meant. I couldn’t always find ratings or know if it was OK for aerial. I think this is normal for a lot of aerialists but it meant I needed to keep doing research.

SWIVEL & BINERS

I ended up ordering hardware from Aerial Essentials because I felt that they had a good website, I knew of other aerialists who have their hardware, and they listed all the ratings in a way that was easy for me to understand. However, now that I’ve done more research, I’ve looked back at their website and have questions about some of the biner ratings and what I received. *2/1/16 Aerial Essentials updated their website & is consistent with what I received.

I bought 3 carabiners thinking I may need one for each spanset connected to the swivel then one to connect to the rigging a point. I also thought about buying a spreader plate & a 4th biner because that would keep the carabiners and swivel from being double loaded. That is probably the best and safest set up but I thought it would take up a lot of room since I was trying to conserve my ceiling height.
*Now that I’m writing this I think I may buy a spreader plate and set it up this way for my aerial rig since height won’t be an issue.* 

Currently, I use 2 carabiners & a swivel. I put both spansets in one carabiner. Attach it to the swivel and then a biner to the rigging point. It’s nice to have an extra carabiner just in case. I also wanted to feel/see the difference between the auto lock & screw gate so I bought both. The auto lock is D shaped. 

UPDATE: 2/1/2016 After doing more research on carabiners (see my carabiner post), I’ve learned that this rigging of a double point Lyra is a mistake. Use of spansets in carabiners will overload the carabiner make it dangerous. Carabiners were not designed for that type of use. Also, tri-loading a carabiner with 2 spansets and a swivel is bad. I’m purchasing some Quick Links or shackles and a rigging plate and post more updates. 

  • X1 Swivel black, aluminum (with stainless steel bearings): 8,000lbs/36kN (Brand Fusion) -Aerial Essentials $45
  • X1 Carabiner black, steel auto lock  (4.5×2.5″): 50kN (Brand Fusion Tacoma, etched 50kN) – Aerial Essentials $17
  • X2 Carabiner black, steel screw gate  (4.5×2.5″): 25kN (Brand Fusion Ovatti, etched 25kN) – Aerial Essentials $15

Total: $98.10 with shipping.

SPANSETS

My Lyra is a tabless, trapeze/straight top, 36″ tall and about 39″ wide.

I needed 2 spansets for it to use as ropes. Searching the Facebook Safety in Aerial Arts forum, I found that Liftall Tuflex is a common brand sling used in aerials.

NOTES:

  • There are many brands and types of spansets out there. Being a newbie to aerial rigging I stuck with what I have seen/used and what was recommended. Common names if you’re searching online: spanset/Span Set/sling/roundsling/stage sling.
    *My Fiance, who is a metal worker/contractor, had no idea what I was talking about when I said “spanset” but I showed him a picture and he called it a sling.*
  • Spansets are usually color coded depending on weight ratings. Violet/purple and green are what I have seen used with Aerial rigging and were recommended by my aerial instructor. I decided green spansets would be good for my use. Mostly because I’m trying to be super safety conscious & I liked the higher ratings.
  • It’s a good idea to keep the labels intact on the spanset otherwise all warranties are void.
  • Also, regular inspections are necessary. Each spanset should come with instruction/warnings about how to inspect them. (I keep a notebook with dates of inspections along with all the specs and purchase dates.)

I priced a dozen different websites before purchasing. I wanted green-rated spansets with black covers and found a recommendation for Sapsis Rigging on the Facebook Safety Group.

Sapsis has several “in stock” spansets and also they will also custom-make sizes if you call and request them. They also were the best price I found for green-rated/black-covered. Unfortunately, the size I actually needed for the studio was not a size they had in stock. And I didn’t know it until I actually rigged it at the studio. I was impatient … I ordered green 4ft ones off of Amazon (Goodness, I’m addicted to Prime!). If you know what size you need you can get away with buying a few spansets. But I like having my options…I bought 8 in four different sizes.
*I called for 4.5′ black-covered spansets and they quoted around $19 each.

Liftall EN60X4 Tuflex sling: Verticle 5300/ chocker 4200/ basket 10600lbs:

  • X2 1 ft green: Sapsis (black) $7.83 each
  • X2 3 ft green: Sapsis (black) $10.17 each
  • X2 4 ft green: Amazon (green) $15.13 each
  • X2 6 ft green: Sapsis (black) $17.20 each

Sapsis (+shipping $14.48) $84.88 + Amazon $30.26 = $115.14

OTHER STUFF

I also bought some athletic tape for the lyra so I can recover it when needed (the gray isn’t my favorite color). I couldn’t decide on a color so I bought black and pink and also gray just in case I wanted touch up the current tape. Maybe I will make a blog when I re-wrap it for the first time.

  • Mueller M-Tape Canister (3 Rolls/Pack) Black (1.5′ x 10 yds) Amazon $11.62
  • Mueller M-Tape Canister (3 Rolls/Pack) Gray (1.5′ x 10 yds) Amazon $11.62
  • Mueller M-Tape Canister (3 Rolls/Pack) Pink (1.5′ x 10 yds) Amazon $11.62
    Total: $34.86

When I finally rigged everything and put the Lyra up in the studio the black coating on the carabiners and swivel rubbed together and makes a creaking noise. I sent an email to Aerial Essentials asking if it was normal and if there was a fix. They recommended using graphite to lubricate it.

  • L-300 Powdered Graphite Lubricant 21.oz: Amazon $6.21

My first jump into owning my own aerial equipment cost me: $504.31

***This is the what I choose to buy & some of my reasons why I chose what I did. It may not be the safest or right choice for you.***

NOTES:

I could have searched and found the hardware cheaper (the black coating costs extra, buying directly from manufacturers costs less) or not bought one carabiner and only bought one set of spansets  …I could have done it for about $360 total (maybe less).

But I’ve already brought my Lyra to a workshop where I needed different size spansets. I also lent some hardware to friends for a NYE performance. Now, I’m going to need the 6-foot spansets for my new outdoor rig (Yep…that will be another blog subject). I am using all the equipment I’ve bought. And have plans to buy more.

This is just the beginning when it comes to aerial equipment. I also need mats. Mats are necessary for aerial safety. Mats are freaking expensive!! (Future blog subject!) Aerial is not cheap. Expect to spend money if you start buying equipment. Plus you still will need to find a safe place to rig it (Future blog subject!). Luckily, I have a few awesome aerial studios that will let me rig from one of their aerial points. Plus, I’m getting a portable aerial rig of my own soon.

lyra

This was my Christmas card on my new hoop and hardware.